强夯机租赁除了日常的使用，日常的维护也是十分的重要，在实际的操作中只有是做好了日常的维护工作，后期的工作才会做的更加的顺畅。下面就来讲讲这方面内容吧。

In addition to the daily use, the daily maintenance of dynamic compaction machine rental is also very important. In the actual operation, only if the daily maintenance is done well, the later work will be done more smoothly. Now let's talk about this aspect.

强夯机租赁车辆转场安装完设备后，应检查各个滑轮以及各个减速器的油量是否充足。检查和保养液压油、发动机机油、冷却水是否需要添加；各油管、气管、水管接头处是否有渗漏现象；蓄电池各接线是否牢固；各仪表灯光以及各电磁阀和开关是否正常工作；各操纵手柄位置是否正确、灵活、可靠。检查液压油油面，如不足应按机型规定的牌号添加，不允许将不同牌号的液压油混合使用。

After the rental vehicle of the dynamic compaction machine is transferred and the equipment is installed, check whether the oil volume of each pulley and each reducer is sufficient. Check and maintain whether hydraulic oil, engine oil and cooling water need to be added; Whether there is leakage at the joints of oil pipes, gas pipes and water pipes; Whether the wiring of the battery is firm; Whether the instrument lights, solenoid valves and switches work normally; Whether the position of each joystick is correct, flexible and reliable. Check the oil level of hydraulic oil. If it is insufficient, add it according to the brand specified by the model. It is not allowed to mix hydraulic oil of different brands.

夯击遍数应根据地基土性、加固要求和施工工艺确定。一般夯击一能达到要求的加固效果，就不该采用多遍夯。村饱和土，由于夯击过程中，孔隙水比不断上升，夯了一定次数以后，夯点的侧向移动和夯坑四周地表隆起加剧.此时夯击能中大部分损耗于挤出变形及孔隙水压升高，不宜连续夯方。若施加的夯击能还不足，需侍上升的孔隙水压消散后再继续进行夯击。

The number of compaction passes shall be determined according to the foundation soil properties, reinforcement requirements and construction technology. Generally, once the tamping can achieve the required reinforcement effect, it should not be tamped for many times. For saturated soil in the village, due to the continuous rise of pore water ratio during compaction, after a certain number of compaction, the lateral movement of compaction point and the surface uplift around the compaction pit are aggravated At this time, most of the compaction energy is lost in extrusion deformation and pore water pressure rise, so it is not suitable for continuous compaction. If the applied tamping energy is not enough, it is necessary to wait for the rising pore water pressure to dissipate before proceeding with tamping.

作业前，检查各系统管路及接头部分应无裂纹、松动和泄漏现象，滚轮的刮泥板应平整良好，各紧固螺栓无松动，确认正常后，方可启动。开动前，机械周围应无障碍物和人员。在运行中，不得进行修理或加油，需要在机械底部进行修理时，应将内燃机熄火，用制动器制动住机械，并楔住滚轮。

Before operation, check that the pipelines and joints of each system should be free of cracks, looseness and leakage, the mud scraper of the roller should be flat and good, and the fastening bolts should be free of looseness. It can be started only after it is confirmed to be normal. Before starting, there should be no obstacles and personnel around the machine. During operation, it is not allowed to repair or refuel. When it is necessary to repair the bottom of the machine, the internal combustion engine should be shut down, the machine should be braked with the brake, and the roller should be wedged.

变换压路机前进或后退方向，应待滚轮停止后进行，严禁利用换向离合器做制动用。在新筑道路上碾压时，应从中间向两侧碾压，距路基边缘不少于0.5m。上坡时变速应在制动后进行，下坡时严禁脱档滑行。碾压傍山道路时，必须由里侧向外侧碾压，碾压第2行时，必须重叠半个滚轮压痕。

Changing the forward or backward direction of the roller should be carried out after the roller stops. It is strictly forbidden to use the reversing clutch for braking. When rolling on the newly built road, it shall be rolled from the middle to both sides, and the distance from the subgrade edge shall not be less than 0.5m. When going uphill, the speed change should be carried out after braking. When going downhill, it is strictly forbidden to slide out of gear. When rolling the road near the mountain, it must be rolled from the inside to the outside. When rolling the second row, it must overlap half of the roller indentation.

以上就是今天为大家介绍的关于问题以及注意事项的全部内容，希望对大家能有所帮助，想要了解更多内容可以电话联系我们或者关注我们的网站http://www.sddhfjx.cn，我们的工作人员会及时与您取得联系。

The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://www.sddhfjx.cn , our staff will contact you in time.